Flasher ARM

Flasher ARM

Flasher ARM is a programming tool for microcontrollers with on-chip or external Flash memory and ARM core. Flasher ARM is designed for programming flash targets with the J-Flash software or stand-alone.

Main features

  • Stand-alone JTAG/SWD programmer (Once set up, Flasher can be controlled without the use
    of PC program)
  • Support for ARM 7/9 and Cortex-M3
  • Ethernet interface
  • No power supply required, powered through USB

Flasher STM8

Flasher STM8

Flasher STM8 is a programming tool for STM8 series of flash microcontrollers.

Main features

  • All STM8 devices can be programmed
  • Integrated optical isolation between host and target system
  • Full duplex 100Mbit Ethernet interface
  • 128 MB internal flash memory to store target program

Flasher PRO — Programmer for ARM7/9/11, Cortex, RX and PPC cores

Flasher PRO is a programming tool for microcontrollers with on-chip or external Flash memory and ARM, RX or PPC core.

Flasher PRO is a programming tool for microcontrollers with on-chip or external Flash memory and ARM, RX or PPC core. Flasher PRO is designed for programming flash targets with the J-Flash software or stand-alone. Flasher PRO connects via USB, Ethernet or via RS232 interface to a PC, running Microsoft Windows 2000, Windows XP, Windows 2003, Windows Vista, Windows 7, Windows 8 or Windows 10 and has a built-in 20-pin JTAG connector, which is compatible with the standard 20-pin connector defined by ARM.

Flasher PRO—Professional Production Programmer

  • Stand-alone JTAG/SWD programmer (Once set up, Flasher can be controlled without the use of PC program)
  • Ethernet interface
  • Supports internal and external flash devices
  • Wide range of devices are supported
  • Free firmware updates
  • 128 MB internal NAND flash, used for storing configuration and data files
  • Serial in target programming supported

Flasher Portable PLUS – Handheld Programmer with Display

The handheld stand-alone Flash Programmer for on-chip and external flash memory. Flasher Portable PLUS is a battery driven programming tool for microcontrollers with on-chip and/or external flash memory. It has been designed to fill the need of an extremely portable, production grade flash programmer used for in-field firmware updates.

Flasher Portable PLUS can be powered by its internal rechargeable battery or USB. Use the integrated 1,8 inch display to review your firmware and programming status.

Initial setup/preparation for stand-alone mode operation is done via the J-Flash software, also used by other Flasher models, which requires a PC running Microsoft Windows 2000, Windows XP, Windows 2003, Windows Vista, Windows 7, Windows 8 or Windows 10.

Flasher Portable PLUS also supports having up to eight configurations/image files stored on the Flasher, so one unit can be used for different targets, versions or configurations. Proper image selection is done by simply clicking a button. The currently elected image is displayed.

Flasher Portable PLUS—The Mobile Flash Programmer

  • Stand-alone in-circuit-programmer (Once set up, Flasher can be controlled without the use of a PC program)
  • Powered by internal battery rechargeable Li-Ion 680mAh, no external power supply required
  • Full insights with the new 1,8 inch display
  • Up to 10 hours programming with one battery charge
  • Supports having up to eight configurations/data files being stored on Flasher
  • Push button allows easy selection between multiple images/configurations stored on Flasher
  • 128 MB internal memory for configuration and data file storage
  • Supports ARM, Cortex, PowerPC and Renesas RX cores.
  • Supports internal and external flash devices
  • Free updates
  • Data files can be updated via mass storage or via J-Flash
  • Target interface: JTAG / SWD / FINE / SPD
  • Programming speed typically between 30 KB/second and 1 MByte/second. Max. programming speed highly depends on target hardware and max. programming speed of the flash itself
  • SECURITY: Flasher Portable and Flasher Portable PLUS support Authorized Flashing. It allows to limit the number of flash programming cycles and to protect the Flasher against non-authorized access in case of external production

Flasher Secure – Secure Production at Contract Manufacturers

Flasher Secure is a mass production programming system, capable of protecting the vendor’s IP regardless of the production site. It provides full control over the programming process at contract manufacturers (CM) and similar environments.

How it works

When you need to go for mass production, it is common to employ a contract manufacturer (CM) to mass-produce products. CMs have access to the customer's IP and enormous quantities of the components they are contracted to produce. Because of this, it is essential that customers control both their IP and limit CM production to prevent theft and secure revenue. To combat these threats, Flasher Secure uses mutual authentication, authorization, and confidentiality to secure your IP and production run. As an IP owner, you have full end-to-end control of your production chain.

End-to-End Security

Flasher Secure supports vendor-specific trusted firmware features to ensure end-to-end encryption, authentication, and confidentiality covering the whole process including the 'last mile'.

Secured Firmware

Modern products carry a huge amount of intellectual property (IP). From the IP owners point of view most of the IP is located inside the firmware. IP owners want to protect their IP. The Flasher Secure system uses authentication algorithms to make sure, that only authorized boot loaders and firmware are used in the system. If one component is not genuine, the device will stop working. Simply copying the firmware and/or bootloader from one device to another is not possible any more.

Flasher Secure—Protect The Vendors's IP

  • Authenticated production with full visibility
  • Production volume control
  • CM administration and setup portal
  • Ultra-fast programming
  • Supports Cortex-M/R/A, RX, PPC
  • Prevents production of counterfeit units
  • No overhead in programming time
  • Secure your production at contract manufacturers

Flasher 5

Flasher 5 is a programming tool for ST9 and Renesas M16C/20, M16C/62, M16C/80, M32C, R8C, R32C, M38 and M79 series of flash microcontrollers in serial mode (1.5 MByte FLASH to store target program, remote control functions for automated testers).

Main features

  • Serial (in target) programming supported
  • PC program allows batch mode processing for usage in automated test systems.
  • Once set up, Flasher can be controlled without the use of PC program

Flasher 5 Pro

Flasher 5 PRO is a programming tool for Renesas M16C/62, M16C/80, M32C, M79, R32C, R8C series of microcontrollers. This tool allows programming of MCU via serial synchronous or asynchronous interface in circuit only. A target system is required.

Main features

  • Serial (in target) programming supported
  • 64MByte internal Flash memory to store target program
  • PC program allows batch mode processing for usage in automated test systems.
  • Once set up, Flasher can be controlled without the use of PC program

Flasher ST7

Flasher ST7 is a programming tool for ST7 series of flash microcontrollers.

Main features

  • Small, compact housing
  • Easy to use windows program
  • 512 KByte internal Flash memory to store target program

sales enquiry button